Showing results: 16 - 30 of 44 items found.
-
A10150 -
Tabor Electronics Ltd.
Model A10150 is an ultra-small footprint, wideband, DC coupled amplifier designed for high frequency, low distortion, signal amplification. With a high bandwidth of 150MHz, 20Vp-p into 50 ohms and a fast transition time of less than 1.8ns, the A10150 is the ideal complimentary amplifier to any high speed signal source that needs a supporting power boost for demanding applications.
-
A10160 -
Tabor Electronics Ltd.
Model A10160 is an ultra-small footprint, wideband, DC coupled amplifier designed for high frequency, high current, signal amplification. With a high bandwidth of 45MHz, 34Vp-p into 50 ohms and up to 10W output power, the A10160 is the ideal complimentary amplifier to any signal source that needs a supporting power boost for demanding applications.
-
9100 -
Tabor Electronics Ltd.
Model 9100 is a Single/Dual Channel, 2U, half-rack size, bench-top power amplifier designed for signal amplification. With unprecedented signal purity, Model 9100 amplifies signals from DC to over 500kHz. The unit has a fixed gain of x15 however the same amplifier is available with custom gain and no signal purity or performance degradation whatsoever.
-
9400 -
Tabor Electronics Ltd.
Model 9400 was designed as a general purpose, wide band and high voltage amplifier however, with specific applications in mind. It has four channels built in a small case size to save space and cost but without compromising bandwidth and signal integrity.
-
9200A -
Tabor Electronics Ltd.
Model 9200A was designed as a general purpose, wide band and high voltage amplifier however, with specific applications in mind. It is built in a small case size to save space and cost but without compromising bandwidth and signal integrity.
-
9200 -
Tabor Electronics Ltd.
Model 9200 is a Single/Dual Channel, 2U, half-rack size, bench-top power amplifier designed for signal amplification. With unprecedented signal purity, Model 9200 amplifies signals from DC to over 500kHz. The unit has a fixed gain of x15 however the same amplifier is available with custom gain and no signal purity or performance degradation whatsoever.
-
9100A -
Tabor Electronics Ltd.
Model 9100A was designed as a general purpose, wide band and high voltage amplifier however, with specific applications in mind. It is built in a small case size to save space and cost but without compromising bandwidth and signal integrity.
-
Holding Informtest
Acts as a bridge between a machine, motor controller, or PLC and related drive amplifier, feedback device and/or software.
-
SY018 -
Synectic Electronics
Our compact strain gauge amplifier can be used in applications requiring 4-20mA or a voltage signal from a strain gauge bridge transducer.
-
Type 132 -
Datum Electronics, Ltd.
The Type 132 Amplifier is designed to amplify the signal from any load cell with full bridge connection, allowing the user to use the data from the load cell in a more efficient and productive way.The Type 132 Amplifier is designed to interface to a full bridge strain gauge based load cell or similar sensor. It can be calibrated to provide a 0-10V output for a fixed load range from the sensor.
-
Type 131 -
Datum Electronics, Ltd.
The Type Load Cell 131 Amplifier is designed to interface to a full bridge strain gauge based load cell or similar sensor allowing the user to use the data from the load cell in a more efficient and productive way.The Type 131 Load Cell Amplifier is designed to interface to a full bridge strain gauge based load cell or similar sensor. It can be calibrated to provide a 4-20mA output for a fixed load range from the sensor.
-
WMA-IB-HS -
Falco Systems
The WMA-IB-HS can be used to double the output voltage of two high voltage amplifiers by driving them in bridge mode, or as high impedance input buffer while maintaining precision, high speed and low noise. Because of its high bandwidth, the WMA-IB-HS model is ideal for the Falco Systems WMA-100 or WMA-300 amplifiers. It can also be used with all other Falco Systems HV amplifiers, or even with high voltage amplifiers of another brand.
-
WMA-IB-LN -
Falco Systems
The WMA-IB-LN can be used to double the output voltage of two high voltage amplifiers by driving them in bridge mode, or as high impedance input buffer while maintaining precision and ultra-low noise. The WMA-IB-LN model has been designed specifically for the Falco Systems WMA-200 high voltage amplifier. Two WMA-200 amplifiers combined with one WMA-IB-LN provide unprecedented noise performance and output voltage range.
-
SY014D -
Synectic Electronics
The strain gauge amplifier is specifically designed to provide signal conditioning for load cells and other wheat stone bridge transducers. With external zero and span trimmers fine adjustment is made and the full scale output can be set anywhere in the range 0.5 to 4.5mv/v.
-
SY046 -
Synectic Electronics
The SY046 Digitally Tareable Load Cell Amplifier is an analogue amplifier with the digital gain advantages. This amplifier can excite up to 4 x 350Ω bridge transducers and provides either a 4 – 20mA, 0 – 5V or 0 – 10V output with a remotely triggered zero offset. This feature is of great value when load cells are difficult to access or other strain gauged components have been installed in difficult environments. The display is very useful during set up and calibration.